JVC SEA-M9 in the house!

Who would think that such an unusual unit would appear on Åland? It’s been kept very well – it’s damn near mint aside from the little scratches on the top. The original service manual was a nice bonus, since it doesn’t seem to be available anywhere on the net.

Advertisements

The Yamaha P-2200 restoration begins

The fun part about giving this guy a first look-through was that it did actually turn on, and it did actually play on both channels … barely. The right channel was heavily distorted and  about half of the time when the power switch was flicked, it’d only flicker and buzz for a while before setting the breaker off.

The turn-on issue was caused by a severely worn-down power switch. The contact surfaces had literally vaporised and disappeared from switching that 1,3 kVA transformer for thirty years. There’s no remedy able to get that into shape for switching big loads again. At least not without giving it a helping hand.

A helping hand in the form of a 230 V relay. I even went the extra step and added a capacitor across the coil in order to make the life of the switch easier.

Testing the relay circuit (animated GIF – clickit!)

While I wouldn’t trust a transformer to this, it should switch the relay for many years to come.

The hot-glued, PVC-taped relay board is simply placed loosely behind the front panel.

It workes very well, however there should be two relays used if you’re to be picky; the original switch is configured to turn the two primary windings on at slightly different times. This is in order to reduce the start-up current somewhat.

(I was later informed that switches such as these, commonly found in AT computer chassis’ would probably work as replacements.)

With the power switch issue out of the way, let’s move on to some intensive maintenance of the actual electronics. Starting with a re-cap.

Two 470 µF capacitors for the size of a thirty-year-old 220 µF

Old and nasty.

Worth noting is that C101 and C201 (100 µF/10 V) were actually completely dried-out; they didn’t even register on the meter. It’s odd that the amplifier worked at all without them, as they seem to be in the signal path.

It’s hard to imagine that these capacitors are both more reliable and more powerful than the old ones.

While new caps are always fresh and nice, it didn’t remedy the right-channel bias issue. The cause for that was two-fold and somewhat unexpected. For starters, the bias adjustment potentiometer looked like this on the inside:

The less obvious issue, however, was that a small (0,47 µF) tantalum capacitor, C113, was shorted. It’s connected across the base and collector of one of the transistors in the bias circuit, as well as across the bias adjustment potentiometer. Short-circuiting C113 is equivalent to turning the bias down to zero.

The affected channel had been serviced before and a lot has been replaced. I’d wager that C113 failed at that time and that the service technician didn’t bother actually listening to the amplifier before giving it back to the customer. Nevertheless, replacing C113 (with a 2,2 µF electrolytic; C213 was also replaced to avoid any channel imbalance) and VR101 (the bias pot) remedied the problem. The channel still has a slight DC offset of 20 mV or so, but I’ll live with that for the moment; there’s still a few transistors that should be renewed.

The same service technician also installed MJ15015 and MJ15016 transistors for the output of the channel – transistors with a maximum VCEO of 120 V! The power supply rails in the P-2200 add up to 160 V; 120 V transistors have no place in such an amplifier. It may work, but any safety margins intended by the designer are lost. If the output terminals are shorted or over-loaded, these transistors will be up in smoke before you can even think “blown outputs”! The proper MJ series transistors to use would be MJ15022 and MJ15023.

For shame.

Anyhow, with that bitter-sweet story out of the way, only the cleaning-up remains. I’ll spare you the narration, enjoy!

And that’s it! The only things remaining to do is to give the incompetently serviced channel another overview in the future, replacing driver transistors and of course outputs. One of the thermal indication thermostats has also failed, so I might replace that some time in the future. That’s a minor issue though.

Thank you for visiting, I hope you enjoyed reading about this project as much as I enjoy listening to it!